PKR-2 is intended for in-place maintenance check of all type (both resistor and reactor type) on-load tap changers (hereinafter – OLTCs) being a part of and not included in a power transformer.
Máy phân tích bộ điều áp dưới tải OLTC của máy biến áp SKB PKR-2
Hãng sản xuất: SKB EP Model: PKR-2 - Yêu cầu báo giá
- Liên hệ
Gọi để có giá tốt
TP. Hà Nội: (024) 35.381.269
TP. Đà Nẵng: (023) 63.747.711
TP. Bắc Ninh: (0222)730.39.68
TP. HCM: (028) 38.119.636
Phạm vi khoảng thời gian đo, sec: 0.01 ÷ 1200
Sai số, sec: ±(3+tx)×10-4
Độ phân giải thời gian, ms: ±0.1
Dải đo chuyển động góc, độ: 2 ÷ 360
Sai số góc, Độ: ±0.56
Dải đo dòng điện trực tiếp, А: 1 ÷ 4
Sai số đo dòng điện, % ±2
Dải đo điện áp trực tiếp, V: 1 ÷ 20
Sai số đo điện áp, % ±5
Dải đo điện trở, Ohm: 1 ÷ 20
Sai số, % ±5
Tốc độ lấy mẫu đo trở kháng mỗi kênh, kHz: 10 ±0.1
Thời gian ghi max (radial diagram measurement) , phút ,:20
Công suất tiêu thụ ở chế độ chờ, W: 15
Công suất tiêu thụ ở chế độ đo lường, W: 210
Dải nhiệt độ hoạt động, ºС: -20 ÷ +50
Trọng lượng, kg: 6.1
Kích thước, mm:360×290×165
Giao diện: English
HDSD: English
Chu kỳ hiệu chuẩn: 3 năm
Cung cấp kèm theo:
- Máy chính, HDSD
- Đầu do dịch chuyển góc DP22
- Kẹp đất
- Tay quay
- Dây nối đất
- Dây nguồn
- Bộ dây đo lường
- Túi đựng
The instrument is completed with a special transducer. Its interface with shafts of different drives is provided with a set of axes and bushings, which are installed without any tools by simply putting on the shaft extension.
Based on the selector and contactor switching sequence circular diagram in case of forward and reversal travel, one may judge on the end play size and selector assembly quality.
All characteristics are taken simultaneously based on three phases for OLTCs located in the neutral conductor of "star-connected" windings, and single phase for OLTCs located in the line of "star-" or "delta-connected windings".
The switchover oscillography enables to detect the actuation delay, non-simultaneity of in phase actuation and bouncing during switchover.
All characteristics are taken simultaneously based on three phases for OLTCs located in the neutral conductor of "star-connected" windings, and single phase for OLTCs located in the line of "star-" or "delta-connected windings".
Check conducted during the drive shaft slow rotation using a handle with simultaneous display of contact closures/openings in degrees and voltage and current values.
No additional elements (for example, resistors) or knowledge of resistances of current-limiting resistors of the checked instrument are required to measure the OLTC parameters. All adjustments to a specific OLTC are performed automatically in the instrument.
The instrument is completed with special long calipers to be conveniently connected to some OLTCs (in this case, it is not necessary to drain oil from the contactor tank).
The instrument may be connected to the on-load tap changer with measuring cables provided with alligator clips without contact calipers with oil being partially drained from the contactor tank or removal of the on-load tap changer from the transformer tank.
The instrument is equipped with a large color high-brightness and high-contrast display facilitating the graph processing.
The measurement results are stored in the non-volatile memory of the instrument, on the external flesh memory, and they may be transferred to the computer.
Therefore, the instrument may be controlled by the PC. It enables to measure diagrams being inside a car with the computer, which is important in winter.
The instrument meets the electromagnetic compatibility requirements to Class A equipment according to GOST R 51522.1-2011.
The instrument meets the safety requirements to electric control and measuring instruments and laboratory equipment according to GOST R52319-2005.
PKR | PKR-2M | |
OLTC check mode | demountable | demountable and in-place * |
Inbuilt battery supply | none | available (operation time from 2 to 16 h) |
* In-place check mode enables to conduct the in-place diagnostics of OLTCs with current-limiting resistors with the contactor tank cover in place. This mode is based on the DRM method (see above) and consists in measurement of current intensity through winding, in which the OLTC is switched on.
Specifications |
Value |
Time interval measuring range, sec |
0.01 ÷ 1200 |
Maximum permissible intrinsic absolute error of time interval measurement, sec |
±(3+tx)×10-4 |
Time interval measurement resolution ability, ms |
±0.1 |
Angular movement measuring range, degrees |
2 ÷ 360 |
Maximum permissible intrinsic absolute error of angular movement measurement, degrees |
±0.56 |
Direct current intensity measuring range, А |
1 ÷ 4 |
Maximum permissible intrinsic relative error of direct current intensity measurement, % |
±2 |
Direct current electric voltage measuring range, V |
1 ÷ 20 |
Maximum permissible intrinsic relative error of direct current electric voltage measurement, % |
±5 |
Direct current electric voltage measurement range, Ohm |
1 ÷ 20 |
Maximum permissible intrinsic relative error of direct current electric resistance, % |
±5 |
Resistance measurement sampling rate per channel, kHz |
10 ±0.1 |
Maximum recording time (radial diagram measurement), min |
20 |
Number of computer communication channels, pcs. |
2 (USB, USB host) |
Maximum consumed power in start standby mode, W |
15 |
Maximum consumed power in measurement mode, W |
210 |
Operation temperature range, ºС |
-20 ÷ +50 |
Maximum measuring unit weight, kg |
6.1 |
Dimensions, mm |
360×290×165 |
Interface language |
English |
User manuals language |
English |
Calibration period, year |
3 |
- Cam kết chất lượng
- Bảo hành chính hãng
- Giao hàng tận nơi
- Đơn giản hóa giao dịch